LED Tail Light
Part Number: 8110115
Available for immediate delivery
This tail light offers both a visual and technical improvement for the GS. The clear Plexiglas housing optically continues the lines of the silver tail. The LEDs are clear when off but shine intensely red when switched on. These high performance LEDs are nearly indestructible and extremely bright. Multiple LEDs replace the single filament of a standard bulb and virtually eliminate the possibility of tail light failure, providing an increase in passive safety. Additionally, the LEDs are brighter than the standard incandescent bulb, making you more visible in all traffic situations.
• Easy installation without permanent modifications.
• Tested by the German safety authority, TÜV
• Everything needed is included in the kit.
• Compatible with Can Bus system
R1200 GS and Adventure owners please note:
1. This part only fit up to and including 2007 models.
2. You can also install one of our tail light covers with this tail light. We have a silver and carbon look cover available. If you do already have one of our tail light covers and you now also want to add this LED tail light, you’ll also need the hardware kit 8110112. All of these items are available under the Related Products tab.
** The images have been updated to reflect the part currently supplied.
• F650 GS Dakar
• G650 GS (all years)
• F800 S
• F800 ST
• F800 R
• R1200 GS up to 2007
• R1200 GS Adventure up to 2007
Average Customer Rating: (Based on 10 reviews)
Already purchased this item? Write a customer review
|Easy to install, good material, looks clean. What can i say its a good buy. I recommend it.|
|I read the reviews by others and went ahead and used a sponge sanding block and removed the \"chrome\" from the new light. The chrome paint comes off super easy with the sanding sponge and 5 minutes later it was all black and looked great. Install on my G650GS was difficult because 2 of the 3 bolts are very difficult to reach and even though I have a lot of tools, nothing worked other than microscopic turns of each bolt with a box wrench (a ratcheting 10mm wrench might have worked better but I don\'t have a metric set of those). THERE ARE ALSO NO DIRECTIONS FOR THE G650GS IN THE BOX OR ONLINE, SO YOU ARE ON YOUR OWN TO FIGURE IT OUT. For the 2012 G650GS, the wires connect directly at the light, so you don\'t have to mess with the old wiring at all, but you end up with a LOT of extra wiring on the new light that you have to tuck somewhere. Re-installatiing the nuts and tightening them was a lesson in patience. Took me 1.5 hours because of the difficult bolt removal and re-installation. For reference, it took me 15 minutes to install Pivot Pegz on this bike.|
|I started having LAMPF! on my 2006 1200 GS Adventure and when I went to put a new bulb in, I noticed how corroded things were back there, so I purchased this LED taillight despite reading some of the negative reviews. The unit looks EXACTLY like the one in the picture here on the website, so I'm not sure if Wunderlich has changed these or not... It was pretty easy to install, but be warned if you have the standard GSA panniers, it is WAY easier to get this installed if you remove the racks for the panniers first, as they bolt into the underside of the bike where the license plate holder is attached. It can be done without removing the racks, but it's much easier after you remove them. Instructions were very good, installation was easy and this thing really puts out a lot more light than the stock bulb. Very happy with this and I don't understand all the negative comments about the cheap look of the plastic that looks like chrome. It all looks fine to me.|
|Overall poor quality. Screws corrode, the paint that is supposed to look like chrome comes off.|
|Fits perfect at my G650GS 2010. it is simple to install, do not need to cut wires. Looks very nice, like a 1200.|
|I installed the light the other weekend. I'm very pleased with the brightness of the light. It was easy to install and looks good perched under the luggage rack and between the pannier racks. Much more visible than the original.|
|My original unit had rusted to the point of being no longer viable. So I shopped around and there's not a lot of choice out there. This unit is incredibly bright, easy to fit and works. Just have others have said though it looks and feels cheap. Let's be honest, it's a GS - there not known for having an easy life and as long as I'm seen that's all I care about. This was a great option and well worth the money. Perhaps an upgrade by blacking it out would appease those fashion riders.|
|In common with other reviewers I was disappointed with the cheap appearance but it was reasonably easy to fit and is very bright. Note that the fitting instructions assume that you don't have the mounting frame for the side cases fitted. If you have side cases you may need to loosen the mounting frame to get access to the rear light assembly.|
|The LED Tail Light is a vast improvement over the stock tail light (bulb) assembly. BUT...the "chromed" housing is pretty cheap looking. I sanded off the "chrome" down to the black plastic, then cut and applied some reflective tape to add some safety features. Overall I'm happy with how it turned out, but was disappointed when I pulled it out of the box.|
|The LEDs and the lens look great and are a lot brighter than the single bulb. Its the housing that doesn't look very good. It looks nothing like the picture on the web site. The housing is made of a cheesy chromed plastic...not something I'd want to put on my GS. I'll be breaking out the good old flat black spray paint soon.|