|
Paralever Slider, Double ShockPart Number: 8160663 Price: $55.00 Available for immediate delivery
|
More Views 
These crash protectors, already proven in racing, keep the tarmac at a safe distance and prevent major damages to the expensive final drive housing. Installation is simple. Remove the original plastic cap, insert the slider and tighten the central bolt. Tightening the bolt expands the sleeve and the slider is locked firmly in place.
The facts:
• Effective protection.
• Highly resistant special plastic.
• User-friendly and quick installation.
• Complete with everything needed.
• Developed by Wunderlich
This item fits the following BMW bike models:
- K1200RSPORT
- K1200GT_2006_on
- K1200R
- K1200S
- R1200GS
- R1200GSADV
- R1200R
- R1200RT
- R1200S
- R1200ST
- HP2Megamoto
- HP2Enduro
- K1300S
- K1300R
- K1300GT
- R1200GSLC
Customer Reviews
Average Customer Rating: 
(Based on 12 reviews)
Already purchased this item? 
Write a customer review
Awesome!! |
| super easy to put on!! |
Odd issue, but figured it out |
| Had an odd issue w/ this part. Out of the package, the nut that expands the slotted cylinder had been tightened onto the bolt so far that it had already started to expand the cylinder, so much so that even after I backed the nut off, the cylinder had been expanded so much that it wouldn\'t fit into the hole on the bike. So I used pliers to crimp the cylinder back to a shape so that it would fit into the intended hole in the paralever. But the next issue was that the rubber sleeve around the cylinder had been expanded to a point that it wouldn\'t fit into the hole on the paralever. So what really should have been a 30 second installation, at most, was instead 10 minutes of fiddling (and cursing) with this thing. Again, all of this was caused by the nut being tightened too far onto the bolt (and thus causing the expansion cylinder to expand) before it was put in the package and shipped. An odd issue. Seems like a quality part otherwise. |
Did not fir my 2011 BMW GS 1200 |
| Well built, but unfortunately did not fit my \'11 GS. It would not fit in flush and would not lock into position. The staff was kind enough to try to help me but I eventually ened up returning it. |
Easy as pie |
| Easy to install... now I hope I will never have to use it! |
Cheap but effective |
| Should be installed as standard from the factory. |
Provide Nice Protection to the rear paralever |
| Very easy installation, the hardest part is removing the OE cap which can be done with a thin blade knife. |
good to have but expensive |
| this may be the only part i'll buy from wunderlich.prices are way too high plus shipping. |
paralever slider |
| snap to install- literally. untested beyond that. only a slide will tell. |
Instructions |
| It would be great if instructions were included with all products.(ENGLISH). Most of us are decent "shadetree"mechanics,but it's that one time,you do one thing,out of step,and you ruin your bike or the part.All these parts are expensive.They are going on BMW's,not used junk. Please enclose English directions/instructions on all of your products. |
No going back |
| ... to the old plastic insert that is (because you'll probably destroy it removing it anyway). This a nice piece (no printing issues on mine). A snap to install. Hope I never need it. |
Paralever Slider - K1300R |
| Easy to install, excellent quality however, logo/motif quite light; appears to be a printing issue. Front wheel sliders ordered at same time had better, clearer marking. |
Slider on an RT |
| Despite the instructions in purely German and lack of clear pictures, the part was very easy to install once you figured out the right order of insert..which wasn't difficult. Very well made, looks good...should do its job fine..but hopefully not!! |
