My Cart: 0 item(s)
R nineT Sixdays 2 Tail Conversion
Fits all R nineT Models
Please note: Some optional parts are model specific
Please note: This is for models with the passenger pegs and pillion frame.
If you DID remove the Passenger Pegs, Pillion Frame and Passenger Seat see our R nineT Sixdays Tail Conversions
Select your Bike Year & Model and then scroll down to view the kits & parts to get started!
We have created R nineT Sixdays 2 Tail Conversion section to help all the R nineT riders transform your rides' tail built in the Six Days style as an homage to the BMW factory motorcycles of the seventies.
Six Days 2 Tail Conversion with many possible combinations to help you get that unique look. Scroll down past the parts section to see six examples and the list of parts used.
Start With
- Six Days Seat Frame with or without Tail Light
- Choose License Plate Holder Style
- Any Additional Accessories Needed
- Add a Wunderlich Seat (Optional)
Customize your R nineT Tail
Our R nineT Sixdays 2 Tail Conversion parts can help you create a unique look for your R nineT model. Scroll down below the parts section to see a few combinations examples we have put together or create your own!
Torpedo Turn Signal Set, Rear
Part #44300000
Classical, little indicators with a small, but very bright light
surface. Match very well with Wunderlich's rear light "DEVILS-EYE" kit.
Resistors not included.
Torpedo Turn Signal Set, Front
Part #44300100
The matching front indicators for the Torpedo LED indicators.
Resistors not included
Bullet Turn Signal Set - Black
Part #36340402
Classic, discreet halogen indicator with high light yield with low power consumption.
Can be used as Front or Rear Indicators.
No Resistors required
View Full Product
★★★★★
Turn Signal Adapter
Part #44960002
The adapter allows for the installation of the most common accessory turn signal, which is fastened using a threaded screw, to the original BMW turn signal attachment.
View Full Product
★★★★★
Resistor Harness 5W 39 Ohm
Part #44109400
Thanks to the practical wiring adapter set with a built in
resister and with standard plugs, there's no longer any need for
soldering work on the cables because the plugs are compatible with the
original plugs. This means all conversion works can also be quickly
undone again with no additional effort. To be used when converting to
LEDs.
Resistor 5w - 39 Ohm
Part #2057413
When LEDs are used instead of the stock bulb option, it can happen that the on-board computer shows "defective lamp" or the LED will not work properly causing the flash sequence to flash irregularly due to the low power consumption. By using the load resistance, the failure report at the on-board computer is avoided and the LED will operate as intended.
View Full Product
★★★★★
LED Turn Signal Adapters
Part #44109100
These adapters significantly simplifies the conversion of an indicator to a round plug both front and back. Thanks to the practical set with standard plugs, there's no longer any need for soldering work on the cables because the plugs are compatible with the original plugs.
The Following Parts are Used:
- SixDays Seat Frame w/ Light
- SixDays Seat Adapter
- Retrosport Plate Holder
- MPIN Indicators
- U.S. License Plate Adapter
The Following Parts are Used:
- SixDays Seat Frame w/ Light
- Brushed Rear Fender
- Retrosport Plate Holder
- Rhombus Rear Indicators
- U.S. License Plate Adapter
The Following Parts are Used:
- SixDays Seat Frame w/ Light
- Brushed Rear Fender
- Zentral Plate Holder
- Turn Signal Bracket Set
- MPIN Indicators
The Following Parts are Used:
- SixDays Seat Frame w/o Light
- Low Plate Holder
- Rhombus Indicators
- U.S. License Plate Adapter
The Following Parts are Used:
- SixDays Seat Frame w Light
- Retrosport Plate Holder
- Rhombus Indicators
- U.S. License Plate Adapter
The Following Parts are Used:
- SixDays Seat Frame w/ Light
- Low Plate Holder
- Original Indicators
- U.S. License Plate Adapter