My Cart: 0 item(s)
Description
Reviews
Bike Fitment
Description
BMW Handlebar Grip Set
Replacements for models with heated grips.
With these replacement grips, it's possible to restore your bike's appearance and comfort. Over time, the rubber wears out and the gripping qualities are reduced. Instead of replacing the entire expensive grip assembly, if you are careful, you will be able to simply replace the grip rubber and save a substantial amount of money. These grips are original equipment quality and a direct replacement for
the original BMW part. Installation requires extreme caution to avoid
damaging the heating elements. We cannot be held responsible if your
heating elements are damaged during installation.
The grips have an inside diameter of 24mm and they are 125mm long with an open end.
Installation tips:
- Remove bar end weights and or throttle lock
- With a sharp razor blade, utility knife etc. very carefully cut along the length of the grips. Be careful not to cut too deeply or you may damage the heating element. Slice just a little at a time until you can tear the grip rubber apart.
- Peel off the old grip rubbers
- Remove as much of the remnants of grip rubber (if present) as you can to make the surface as smooth and clean as possible
- Install the new grips **
- Reinstall bar end weights and ensure that they are tight. Thread locking fluid is recommended on the bar end weight bolts and it may be necessary to re-adjust your throttle lock if you have one.
** When installing the grip rubbers, you will need to use something that will act as a lubricant for installation and an adhesive thereafter. Some ideas are a universal spray adhesive or rubber glue and some brands of hair spray have been known to work very well. Whatever agent is used, apply to the inside of the grip and the heating element, then quickly slide the grip on and twist and position it as needed immediately before the lubricant dries.
Please note: Not compatible with models that have the Multi Controller on left handlebar.
Reviews
Write a review
13
0
0
2
1
Ron L | May 23rd, 2022
Carefully removed the old worn out grips without too much trouble. The new grips fit perfectly. Love the feel, and the heat transfer from the heating element works incredible. Definitely recommend.
Jason Haines | August 30th, 2019
As long as you take your time removing the original grip, these replacement grips fit well and go on easy. The original ones on my bike (2006 K1200 R) were worn "paper thin" and were easy to slice and peel off, with no damage to the heating element.The left grip had to have a small relief cut out near the flange end so it would clear the heating element end. I used Scott grip glue for installation and this allowed the new grips to slide right on without any modification to the underlayment. Can't emphasize enough to take your time cutting the grip off a with a sharp hobby blade. Hope this was helpful, thanks!
Breck E | August 29th, 2019
Love these grips. Fit is excellent and they work great with the heated grips on my r1150 GS. Installation took all of 15 minutes. I’d definitely use these again!
Show All Reviews
Popular Products
Bike Fitment
BMW K1200 RS
1997
· 1998
· 1999
· 2000
· 2001
· 2002
· 2003
· 2004
· 2005
BMW R nineT
2014
· 2015
· 2016
BMW R1200 GS
2004
· 2005
· 2006
· 2007
· 2008
· 2009
· 2010
· 2011
· 2012
BMW R1200 GS Adventure
2005
· 2006
· 2007
· 2008
· 2009
· 2010
· 2011
· 2012
· 2013
BMW R1200 R
2006
· 2007
· 2008
· 2009
· 2010
· 2011
· 2012
· 2013
· 2014
BMW R1200 RT
2005
· 2006
· 2007
· 2008
· 2009
· 2010
· 2011
· 2012
· 2013
BMW HP2 Megamoto
2006
· 2007
· 2009
· 2008
BMW HP2 Sport
2008
· 2009
· 2010
· 2011
BMW R1200 C
1997
· 1998
· 1999
· 2000
· 2001
· 2002
· 2003
· 2004
· 2005
BMW R1200 CL
2002
· 2003
· 2004
BMW R1200 S
2006
· 2007
· 2008
BMW R1200 ST
2005
· 2006
· 2007
· 2008