My Cart: 0 item(s)
R1200/R1250 RS Tail Conversions
Fits the following models:
- R1200 R 2015-2019
- R1250 R 2019+
- R1200 RS 2015-2019
- R1250 RS 2019+
The long license plate holder of the R12XX R and R12XX RS is anything but beautiful and sticks out like a sore thumb. This tail section and fender eliminator kit is made of robust black plastic. It the basis for cleaning up and creating a sharp and tidy tail!
Several license plate mounting options, Seat and Indicator upgrades. Choose one of our pre-made Kits or create your own. Some combinations can use the original indicators.
Depending on your chosen Tail Conversion you can use your original Indicators or upgrade to MPIN or Rhombus LED indicators.
Upgrade your seat to a Wunderlich AKTIVKOMFORT Seats for a significant improvement in rider & passenger comfort.
View Full Product
★★★★★
Wunderlich AKTIVKOMFORT Seats
Part #30900302-402
Available in:
- Standard Height Rider Seat
- Low Height Rider Seat - 20mm Lower then Standard Seat
- Tall Height Rider Seat - 20mm Taller then Standard Seat
- Passenger Seat
View Full Product
★★★★★
Rear Inner Fender Extender
Part #41590202
This splash guard protects the shock, shock mounts, swing arm, collector pipes and
rear of the gearbox. In addition, helps eliminate water splashed up from the rear wheel onto a passengers feet and legs.
Turn Signal - Kellermann Bullet 1000
Part #7050320-28
The Bullet 1000® DF is a rear indicator in combination with a rear running lights and brake light function. It replaces the existing turn signal indicators, and can be utilized for the brake and rear running light. The light of the continuously glowing red rings give the tail of the motorcycle a spectacular look.
Resistors are not included.
View Full Product
★★★★★
Turn Signal Adapter Set
Part #44960002
The adapter allows for the installation of the most common accessory turn signal, which is fastened using a threaded screw, to the original BMW turn signal attachment.
View Full Product
★★★★★
LED Turn Signal Adapters
Part #44109100
These adapters significantly simplifies the conversion of an indicator to a round plug both front and back. Thanks to the practical set with standard plugs, there's no longer any need for soldering work on the cables because the plugs are compatible with the original plugs.
View Full Product
★★★★★
Resistor Harness 5W 39 Ohm
Part #44109400
Thanks to the practical wiring adapter set with a built in
resister and with standard plugs, there's no longer any need for
soldering work on the cables because the plugs are compatible with the
original plugs. This means all conversion works can also be quickly
undone again with no additional effort. To be used when converting to
LEDs.
Resistor 5w - 39 Ohm
Part #2057413
When LEDs are used instead of the stock bulb option, it can happen that the on-board computer shows "defective lamp" or the LED will not work properly causing the flash sequence to flash irregularly due to the low power consumption. By using the load resistance, the failure report at the on-board computer is avoided and the LED will operate as intended.
View Full Product
★★★★★
License Plate Holder, Swing
Part #38982002
This license plate holder is not only a real eye catcher in itself, it allows an unobstructed view of the rear wheel and tail section. The wiring for the license plate illumination invisibly passes through the inside of the tubing.
US License Plate Adapter
Part #38981444
This adapter has been designed for mounting US license plates to the Wunderlich license plate brackets.
Sport License Plate Holder
Part #38982102
Create your own Tail Conversion
Our License Plate Holder Sport is a stark contrast to the ugly, protruding original. Light, elegant and noble. This plate holder gives the tail section an optically lighter and sportier line.