Part # 26660300
Wunderlich Folding Headlight Guard

This looks great once installed. Read the review for installation tips for mounting the lexan with the rubber fastener from Tom Brown, it'll help. I didn't and spent time doing what he did trying to figure out how to attach the lexan to the frame. This is a very high quality piece and well engineered. Highly recommend.

Well engineered and designed. This was my choice over several of the other guards that are offered for my 2023 1250 GSA. It has a great folding mechanism and it’s easy to clean both the Lexan and the headlight. Installation is a bit tricky, but the video is very good. Written instructions are very marginal. on my trim, triple black, I had to manually pull back the plastic fascia in order to get the lower nut to fit down into the recessed channel for the lower Allen screw. For the Lexan connection to the metal frame, the screws for the rubber washers are purposely slightly short, and you have to put some tension /pressure on these as you are screwing them into the rubber washer in order to capture the thread and provide compression as you are screwing the screw into the threaded component of the rubber nut. You Do not need to buy longer screws as some have suggested. Overall, I give this five stars and it definitely complements the engineering of the BMW MOTORCYCLE

There is a key point that is missed in the instructions. I have a GSA and wanted a Lexan cover for the headlight. The Lexan piece screws in with 4 fasteners. They thread through the holes in the holder and the Lexan, then into 4 rubber posts with a brass threaded piece inside. If you put this together as the illustration shows, the 4 screws will not touch the inner threads of the rubber posts. So...you have to really push hard on them until they do...and this is not made clear. I tried putting the posts in backwards and lots of other things before finally trying this. I was about the return the whole thing. When you push hard, the threads can engage, then they compress the rubber cause it to expand against the holes in the Lexan, holding it firmly close to, but not touching the metal holder and away from the light source. Perfect!!! It's a great design. The resistance of the hinges can be adjusted by tightening or loosening the threaded hinge bolts a litle. The washer set allows them to hold the tension. I put a little vaseline in the rubber fasteners to make them a little easier to undo. They're pretty tight. Silicone would probably do as well or better. I wanted something that would be easy to clean, wouldn't destroy the optics of the light and would look good. This does all that. Great!.

Originally with my bike, I had ordered the OEM headlight guard, but when I started to install it, I was sorely disappointed so I took it back. It leaves a gap in between the headlight and the screen which makes cleaning the surface of either quite difficult, unless you get some tools and remove it. I really like how this one has a hinge on the bottom and you just swivel it down to clean it. While it is attached, it's really a strong hold, so even over rough road it has not come undone.

This is a must have accessory, typically made well and easy enough to fit. My two very small complaints with it are: 1, The Self Locking Nuts that are supplied to attach the “Studs” for the quick release sockets, are far too stiff to fit to the Plastic stud. There is no way to hold the stud without damaging it while doing up the nuts. I replaced these with standard nuts and spring washers. 2, If at all possible, could the hinge points have been designed to be Behind the guard rather than out in front. Just a small issue, but it may have looked better.. Fast and efficient delivery to NZ. Thankyou.

These are a must have item, which provides great protection to your headlight. They are well made, with a typical top quality Wunderlich finish. Yes the fitting instructions are somewhat vague, but easy enough to follow, when all of the parts are laid out and the bike in front of you. The only fault I found, was that the self locking nuts provided to attach the quick release “Studs”, are too stiff for the plastic studs they hold, requiring a very high torque to fit. I ended up discarding these nuts and replacing with standard nuts and spring washers. As far as aesthetics go, I wonder if it would have been possible to put the hinge points “behind” the lense, rather than out in front? Otherwise this is a very good product. Quick delivery to N.Z. as well.

I ordered and installed the Wunderlich headlight guard on my 2019 BMW R1250GS and I must say that it is an incredible piece of engineering just like the bike. The four-point mounting ensures that the frame is secure, the lens benefits from a metal surround and it is hinged at the bottom to allow it to pivot out of the way for easy headlight lens cleaning. It is secured in place with two rubber grommets that plug onto two male adapters at the top ensuring a secure fit. Now the bad news... like other Wunderlich products, the instructions relay almost exclusively on images and photos to show how the unit is assembled. Given the number of parts and limited level of detail, these are incomplete at best and I had to rely on a BMW technician who had installed these before in order to correctly assemble the device. Also, if your BMW R1200GS/R1250GS is equipped with auxiliary lights, the bolts that are provided won't work and the longer bolts required are not supplied -- another reason that the BMW technician had to come to my rescue. These two latter issues are the only reason I "dinged" this product from receiving a 5-star rating -- otherwise the construction is absolutely superlative.